Difference between revisions of "Main Page/PHYS 4210/Sonoluminescence"

From Physics Wiki
Jump to navigation Jump to search
Line 1: Line 1:
 
<h1>Sonoluminescence and Blackbody Radiation</h1>
 
<h1>Sonoluminescence and Blackbody Radiation</h1>
  
 +
<math>\pi^2 <\math>
 
<p>Sonoluminescence is the process by which a gas bubble trapped at the antinode of an ultrasonic standing wave emits visible radiation. This strange phenomenon will be the platform on which 3-dimensional standing waves and black-body radiation will be investigated.</p>
 
<p>Sonoluminescence is the process by which a gas bubble trapped at the antinode of an ultrasonic standing wave emits visible radiation. This strange phenomenon will be the platform on which 3-dimensional standing waves and black-body radiation will be investigated.</p>
  

Revision as of 09:49, 2 June 2015

Sonoluminescence and Blackbody Radiation

<math>\pi^2 <\math>

Sonoluminescence is the process by which a gas bubble trapped at the antinode of an ultrasonic standing wave emits visible radiation. This strange phenomenon will be the platform on which 3-dimensional standing waves and black-body radiation will be investigated.

Introduction

Single bubble sonoluminescence, hereafter abbreviated SL, was discovered in the late 1980's and has since received a great deal of attention. This remarkable process involves, at its core, trapping a gas bubble at a sonic antinode location in a resonance mode of a cell. The exact geometry of the cell is not important but it is necessary that there exist a spatial pressure gradient in order for the bubble to be positionaly stabilized. In the presence of the alternating cycle of acoustic pressure the bubble expands and collapses. When the amplitude of the pressure becomes large enough the collapse of the bubble enters a new regime in which the radius collapses to its hard core limit heating up the gas contents inside and emitting a very brief but copious amount of light. This light can be seen with the unaided eye. Although the emission mechanism along with a number of other properties of SL are still not fully understood, the basic hydrodynamic equations governing the gross motion of the bubble have been around for quite some time and do accurately describe over 99.9% of the bubble's motion. The Rayleigh Plessett equation shown below has been used extensively to describe the motion of the bubble in its many regimes. Eq (1)

SL eqnINT1.png

(1)

with the boundary condition at the fluid gas interface given by

SL eqnINT2.png

(2)

and the use of a van der Waals hard core a in the ideal gas law to give a gas pressure Pg

SL eqnINT3.png

(3)

where R is the bubble radius, c is the speed of sound in the fluid, ρ is the density, η is the viscosity, σ is the surface tension, Pa is the acoustic pressure, and Po is the ambient pressure.

A graph of the bubble radius and driving amplitude as a function of time is shown in Figure 1. This graph was generated by a numerical integration of Eq. 1.

SL fig1.png

Figure 1

Among the first properties that were observed was the very brief nature of the light emission. Initial measurements using high speed photomultiplier tubes placed an upper limit of 50 ps on the emission time. Recent measurements using time correlated photon counting techniques have shown a diversity of emission times depending on the gas contents, with some emission times as long as 350 ps. Another observed property was the enhancement of the light emission by the doping of the water with a small concentration of noble gases such as Ne, Ar, and Xe.

The phenomenon of sonoluminescence is not the focus of your investigation. The details presented above were only presented in order to provide you with some context for what you will be observing. The exact mechanism of the light emission is not fully understood, for more details see M.P. Brenner 2002.[1] For the purpose of this experiment, we will assume that the light emitted from the sonoluminescence is due to blackbody radiation.

.

3D Standing Waves

Waves in three-dimensional space can be described by the wave equation.

SL eqnINT4.png

(4)

In a rectilinear coordinate system, the solution to the wave equation has the following form:

SL eqn2.png

(5)

Where X,Y, and Z have the familiar forms:

SL eqn3.png

(6)

The cos is chosen when the boundary is a pressure release (i.e. not rigid) and the sin is chosen when the boundary is rigid and the velocity at the boundary must be zero. The eigen frequencies are given by:

SL eqnINT7.png

(7)

where v is the speed of sound in the medium, nx,ny, and nz are the orders of the mode, and Lx, Ly, and Lz are the physical dimensions of the cavity.

The Ultrasonic Horn

The ultrasonic horn is used to deliver acoustic power to the volume of water. Internally, the horn contains a series of annular shaped disc transducers which are bolted into its base. The basic structure and shape of the horn is designed to efficiently couple the pressure waves generated from the transducers to the narrow stem of the horn. All of the transducers are the same. They consist of a ceramic material which has been prepared in such a manner as to have a permanent polarization. In other words,there are specialized capacitors. As a charged is placed across this capacitor there is a force generated across the ends, and the capacitor wants to separate. Since the transducers are compressed, this repulsive force does not physically expand the disc but does produce dynamic pressure. As the charge across the transducer is reversed, there is now an attractive force which results in a negative pressure amplitude. The capacitance of the particular tranducers used is 11 nF. In order to efficiently couple electrical power into the transducers, it is advantageous to connect an inductor in series to achieve electrical resonance as given by the formula:

SL eqn0.png

The particular ultrasonic horn used has components which make it tuned for a frequency from 25kHz to 27kHz. Outside of those ranges, the acoustic energy available in the horn is strongly attenuated.

The Cell

The cell is a plastic container onto which is epoxied a small ceramic transducer that serves as a microphone. Since this transducer is not compressed small fluctuations in its diameter produce a measurable signal. By attaching this transducer to the bottom of the cell, one can easily detect when the pressure is the cell is in resonance by looking for large amplitude sine waves on an oscilloscope at the ultrasonic frequency. The cell is provided with a black shroud which has a circular opening on one side which allows light from the SL to enter the photomultiplier tube, but minimized stray light from entering the PMT.

The Photomultiplier Tube

A photomultiplier tube (PMT) is a device which coverts one incident photon into a large pulse of electrons which can then be read out on an oscilloscope. The photon passes through the glass enclosure of the PMT and liberates an electron from a coated surface, this electron is then accelerated by static electric fields into dynode 1, and this initial electron frees many more electrons from the surface. This bunch of electrons then accelerates into dynode 2 freeing a yet larger bunch of electrons. This process continues many times such that even one incident photon can produce a measurable number of electrons at the output. A PMT is a very sensitive optical detector. Due to the high sensitivity, having too many photons entering the PMT can damage the device, and this should be avoided. Even with the black shroud covering the cell, you should not apply power to the PMT without also shutting of the room lights.

The Fluke 412B power supply will provide the high voltage required to bias the dynodes of the PMT. Typically, the PMT should be run at around -1000 V. The PMT will output a negative going pulse with a sharp rise time and a relatively slow fall time. The amplitude of this pulse is related to the number of photons hitting the PMT during a particular pulse. In this experiment, the effect of Sonoluminescence only occurs once during an acoustic wave period, hence, the SL bubbles is flashing at around 27 kHz. The PMT will output pulses synchronized with the acoustic frequency whose amplitude is related to the brightness of the sonoluminescence.


BlackBody Radiation

For a full treatment of blackbody radiation, refer to any Modern Physics textbook. All matter with a temperature greater than 0 Kelvin emits electromagnetic radiation. This common phenomenon is noticed in everyday life when you look inside your toaster, use a stove-top, or bask in the sunshine. The spectrum of emitted radiation depends on the properties of the particular material, and the temperature as described by Planck's Formula:

SL eqn planck.png

(8)


Related to Planck's formula is the Wien Displacment Law, which describes the wavelength at which the most energy is being emitted.

SL eqn wien.png

(9)

Using the above formula, one can determine that the Sun, which appears yellow (~500nm) has a surface temperature of around 5800 K. In this experiment, you will be amazed to see the SL bubbles emitting blue/white radiation, suggesting a much higher temperature!



Procedure

Required Components

  1. Flask
  2. De-ionized Water
  3. Vacuum Pump
  4. HP33258 Function Generator
  5. TDS2014B Digital Oscilloscope
  6. SL100B Sonoluminescence Control Box
  7. Ultrasonic Horn
  8. 1P28 PhotoMultiplier Tube
  9. Various Optical Filters
  10. HV Power Supply

Degas the water

In order for the water to support a sonoluminescence bubble it is necessary for the water to be partially degassed. To do this, start with approximately 600 mL of deionized water in a flask, place a rubber stopper in the top of the flask with a tube passing though it, then attach a roughing pump to end of the tube. The boiling point of water is reduced to below room temperature if the pressure in the flask can be reduced below ~25 torr. The vacuum pump you are using can easily achieve that. You will notice rapid bubbling of the water inside the flask after the pump is turned on. For the first 20 minutes, have the flask on the magnetic stirring platform, and set the Stirrer Control to > 80. After 20 minutes, place the flask into a bath of ice water (if available) and continue pumping for a further 10 minutes, as the sonoluminescence effect is greater when the liquid is at lower temperatures.[2]

SL fig degas.png

Figure 2 - Degassing the water.

Once the degassing procedure is complete, turn off the vacuum pump, and slowly open the pressure relief wave. Then, gently pour the water into the cell being careful not to introduce more bubbles. Fill the cell to the correct level to allow for standing waves whose frequency is near 25-27kHz for the [1,1,2] mode (Hint: solve Eqn. 7 for Lz.)

Electrical Connections

The basic setup for the experiment is shown in Figure 3. The acoustic frequency is provided by a 1 Vpp sine wave from the HP3325A synthesizer/function generator. The appropriate resonance frequency, as determined by cell geometry is around 26kHz. This sine wave is then amplifier by the SL100B control box, and fed into the ultrasonic horn. To electronically view the effects of sonoluminescence, the output of cell transducer is put to Channel A of the oscilloscope, Channel B of the scope should be the High Freq. Output of the transducer. This High Freq. Output filters the cell transducer signal with 150 kHz high-pass filter since the effect of a trapped bubble is to cause a high frequency response. There are two connections made from the Sonoluminescence SL100B to the cell box- a multi-pin power/control cable, and cell transducer input using coaxial connector.

SL setupB.png

Figure 3 - Electrical Connections.


Observe trapped bubbles and Sonoluminescence

Once the water is added, place the black shroud around the cell. Lower the ultrasonic horn into the cell such that the tip of the horn is 5mm - 10mm below the surface of the water. Set the drive amplitude of the ultrasonic horn to 3/4 of maximum. The frequency of the function generator should be adjusted in steps of 10Hz to maximize the signal picked up by the cell transducer. Note that you will observe an electrical resonance centered at 25.9kHz, where the maximum signal picked up on the cell transducer will be about 4 as read off of the analog scale on the SL100 unit. This is not standing wave resonance. The standing wave resonance will have a much high amplitude signal (as high as 12) on the analog meter. Depending on the amount you have filled, you may observe modes other than the [1,1,2] mode as you tune the frequency of the function generator. When you are near the resonance you will see the amplitude rapidly increase as you adjust the frequency, and then begin to decrease as you continue increasing the frequency. Record and plot this relationship between applied frequency and cell transducer voltage. Typically, the quality factor of the resonance should be on the order of 100 to 200.

Set the frequency to the peak of acoustic resonance, the drive amplitude should be adjusted such that the analog meter reads around 4 and so that the output of the cell transducer is an undistorted sine wave. The conditions for SL to occur are very precise- it the drive amplitude is set to low, then no SL will be observed, if the drive amplitude is set too high (greater than 5) then the trapped bubbles jitter and and are lost from the trap.

Now that there is an acoustic standing wave inside of the cell, you can attempt to trap a bubble. To introduce a bubble into water, submerge the heater filament such that it is near (but not touching) the bottom of the cell. Briefly press the boiler button on the SL100B, this will boil a tiny amount of water near the filament creating small bubbles. With the room lights on, you should then be able to see a bubble held stationary in the cell at the location of an antinode. Now, turn off the room lights except for a small desk lamp. You may be able to see the bubble giving off a blueish-white light. If you cannot see the sonoluminescence, try increasing the drive amplitude- keeping an eye on the oscilloscope to ensure a bubble is still trapped. If you loose the bubble from the trap, you will need to load the trap again with another bubble.

SL nobubble.png

Figure 4a - No evidence of trapped bubble on oscilloscope.

SL bubble.png

Figure 4b - Clear evidence of trapped bubble on oscilloscope.

Questions

  1. Draw the a sketch illustrating the [1,1,3] mode inside of the cell, and indicate possible locations to trap bubbles.
  2. What level would you have to fill to for the [1,1,1] mode?
  3. Draw the a sketch illustrating the [1,1,2] mode inside of the cell, and indicate possible locations to trap bubbles.

Detect the Sonoluminescence using a PMT

With the HV power supply still switched off, adjust the height of the PMT and bring it close to the opening in back of the black shroud. Once you have a trapped, sonoluminescence bubble, close the front viewing flap. Turn on a small desk lamp, and shut off the main room light. Turn on the HV power supply to about 1000V and look on the oscilloscope for pulses synchronous with the acoustic radiation. If the peak of the pulses exceeds 500mV amplitude, reduce the operating voltage of the PMT by 50V.

Saving scope traces

There is a Labview program called "TDS2014B read scope" on the desktop. You can use this to save all four scope traces to a tab delimited file (.txt) or a comma sperated file (.csv). The files will be saved in the directory "ScopeData" on the desktop.Please email yourselves the resulting files. DO NOT USE YOUR USB KEY IN THE LAB COMPUTERS. (We'd like to keep the lab computers as virus-free as possible.).

Questions

  1. Sketch or present the waveforms of for the cell transducer output and "High Freq. Output" when a bubble is trapped.
  2. Determine the rise time and decay time of the PMT pulses.
  3. What distribution of peak heights do you observe?

Determine the Temperature of the SL

To determine the temperature of the SL bubble, we will use the assumption that the amplitude of the peak output from the PMT is proportional to the number of photons input to the PMT. There are some important factors which first need to be considered.

  • The SL bubble is inside of the cell, and light has to travel half of the cell thickness through water. The absorption of water as a function of wavelength is:

    SL abs water.png

    Figure 5 - Absorption of Water [3][4]

    A table of the above values is given here: Water_Absorption.xls, Water_Absorption.txt

  • The photons from the SL must then pass through the plastic cell wall. For the purpose of our measurement, we will assume that all wavelengths pass through equally. Comment on the suitability of this assumption for light in the visible spectrum.
  • The PMT does not respond equally for all wavelengths. The efficiency as a function of wavelength is shown below.

    SL eff pmt.png

    Figure 6 - PMT Efficiency.[5].

    A table of the above values is given here: SL_PMT_efficiency.xls, SL_PMT_efficiency.txt

In addition to the above effects, you are provided with four optical filters which you will use to attenuate the SL in a controlled way. The transmission properties of each of the four filters is given in the figure below.

SL filters.png

Figure 7 - Filter transmission as function of wavelength.

A table of the above values is given here: SL_filters.xls, SL_filters.txt

It is your task to determine the temperature the sonoluminescence bubble based on the ratio of the average pulse heights of the PMT signals when the various filters are in place, taking into account the known absorptions and efficiencies of the system. Please carefully explain the algorithm for your analysis in your write-up.


References

  1. M.P. Brenner,"Single-bubble sonoluminescence", Rev. Mod. Phys., 74, 425 (2002)
  2. G.E. Vazquez and S.J. Putterman, "Temperature and Pressure Dependence of Sonoluminescence", Phys. Rev. Lett., 85, 3037 (1999)
  3. R. C. Smith and K. S. Baker, "Optical properties of the clearest natural waters (200-800nm)", Appl. Opt., 20, 177 (1981).
  4. R. M. Pope and E. S. Fry, "Absorption spectrum (380­-700nm) of pure water. II. Integrating cavity measurements", Appl. Opt., 36, 8710 (1997).
  5. Taken from Hamamatsu 1P28 datasheet.